How To Install A Vinyl Fence Youtube

Vinyl siding installation should be left to the pros unless you're confident that you take acceptable carpentry skills and feel. The upside of doing the project yourself is that you tin cut the cost of installation to almost one-half of what you will likely shell out to hire a contractor. The installation of vinyl siding itself is not that hard, just it does require proper planning too as precise measurements, calculations, cuts and leveling to ensure that the panels fit your wall perfectly.

The steps for vinyl siding installation below assume that you have completed installing the panels for the soffit, which is the underside of the roof overhang, and the fascia, which is the horizontal band along the bottom of the roof. For this project, you will need the following tools:

Ability saw Hammer Tin can snips Utility knife Tape mensurate Chalk line Level Ladder

Autonomously from vinyl siding panels, the other needed materials are:

Starter strips J-trims Corner moldings Utility trims Drip caps Housewrap and A lot of nails, preferably those with wider heads Plywood

Keep in mind that even many pros prefer not to accept this chore on alone. Have one or two friends help you. Once you take all tools and materials listed higher up, you're ready to take on this vinyl siding installation DIY.

Step Remove Obstacles

Clear the wall of anything that volition go in the way of the vinyl siding such as exterior lamps, retractable clothesline spools, address plates or old vinyl sidings. Program the disposal of your old siding properly. Don't mess with utility fixtures or the electric meter. You lot need to work effectually them.

Take Measurements

Mensurate from the eave down to the lesser where yous'll nail the starter strip. Most vinyl sidings are 12 feet long and eight inches broad. This means that if the distance betwixt the eave and the bottom is divisible by 8 inches, you tin can connect your top panel directly to the J-trim. About of the fourth dimension, however, yous volition have to modify your last tiptop panel and use a utility trim to install this final piece.

Discover Your Level Points

Detect the level points at the bottom for the starter strip and mark them with the chalk line. Try to be as precise every bit possible with the level points. This will make the task easier as you beginning installing the vinyl siding.

Attach the Starter Strip and Vertical Trims

Align the starter strip advisedly along the chalk line and nail it firmly to the wall. Nail 3 ½ inch by ½ inch plywood pieces along the top of the starter strip to make it sturdier and assistance it hold upwards the vinyl siding panels. Next, attach the vertical trims, including the corner posts and end channels. You lot may likewise attach the trims effectually the windows and doors at this point.

Cut the Vinyl Sidings According to Length

Measure the distance betwixt the vertical end posts and cutting the vinyl panels according to length for each row. Allow for a ¼ inch altitude between the end of the siding and the corner mail. Increase the distance to ⅜ inch in areas where the temperatures become as low equally 40 degrees Fahrenheit. Vinyl siding expands and contracts along with temperature fluctuations. The gap will prevent damage to the siding.

Install the Vinyl Sidings

Sheath the first few anxiety higher up the starter strip with the insulation or moisture protection fabric, and then snap and lock the first vinyl siding row on the starter strip. Nail the panels every maximum of sixteen inches on the framing studs or furring on the wall. It is of import to remember not to smash the vinyl sidings tightly against the wall and position the nail at the heart of the slot; leave a 1/32 inch gap between the nail head and the vinyl siding. You've installed each panel correctly if the siding can freely movement from side to side. When you lot need to overlap panels to span a gap betwixt posts, brand certain that the panels overlap by well-nigh an inch. Work your style up around the wall cut around doors, windows and lamps using the tin snip.

Finish Upward

Equally you lot reach the soffit on the eaves, measure the width that you need for the last piece in several locations and alter the vinyl siding panel according to the measurements. Install a J-channel. Make tabs on the cutting edge of the panel every six inches using a snap lock punch. Install a utility trim into the J-channel. Lock in the last panel that yous have modified on the terminal row and snap it into the utility trim on tiptop of the wall.